.. currentmodule:: pyb .. _pyb.SPI: class SPI -- a master-driven serial protocol ============================================ SPI is a serial protocol that is driven by a master. At the physical level there are 3 lines: SCK, MOSI, MISO. See usage model of I2C; SPI is very similar. Main difference is parameters to init the SPI bus:: from pyb import SPI spi = SPI(1, SPI.MASTER, baudrate=600000, polarity=1, phase=0, crc=0x7) Only required parameter is mode, SPI.MASTER or SPI.SLAVE. Polarity can be 0 or 1, and is the level the idle clock line sits at. Phase can be 0 or 1 to sample data on the first or second clock edge respectively. Crc can be None for no CRC, or a polynomial specifier. Additional methods for SPI:: data = spi.send_recv(b'1234') # send 4 bytes and receive 4 bytes buf = bytearray(4) spi.send_recv(b'1234', buf) # send 4 bytes and receive 4 into buf spi.send_recv(buf, buf) # send/recv 4 bytes from/to buf Constructors ------------ .. class:: pyb.SPI(bus, ...) Construct an SPI object on the given bus. ``bus`` can be 1 or 2, or 'X' or 'Y'. With no additional parameters, the SPI object is created but not initialised (it has the settings from the last initialisation of the bus, if any). If extra arguments are given, the bus is initialised. See ``init`` for parameters of initialisation. The physical pins of the SPI buses are: - ``SPI(1)`` is on the X position: ``(NSS, SCK, MISO, MOSI) = (X5, X6, X7, X8) = (PA4, PA5, PA6, PA7)`` - ``SPI(2)`` is on the Y position: ``(NSS, SCK, MISO, MOSI) = (Y5, Y6, Y7, Y8) = (PB12, PB13, PB14, PB15)`` At the moment, the NSS pin is not used by the SPI driver and is free for other use. Methods ------- .. method:: SPI.deinit() Turn off the SPI bus. .. method:: SPI.init(mode, baudrate=328125, *, prescaler, polarity=1, phase=0, bits=8, firstbit=SPI.MSB, ti=False, crc=None) Initialise the SPI bus with the given parameters: - ``mode`` must be either ``SPI.MASTER`` or ``SPI.SLAVE``. - ``baudrate`` is the SCK clock rate (only sensible for a master). - ``prescaler`` is the prescaler to use to derive SCK from the APB bus frequency; use of ``prescaler`` overrides ``baudrate``. - ``polarity`` can be 0 or 1, and is the level the idle clock line sits at. - ``phase`` can be 0 or 1 to sample data on the first or second clock edge respectively. - ``bits`` can be 8 or 16, and is the number of bits in each transferred word. - ``firstbit`` can be ``SPI.MSB`` or ``SPI.LSB``. - ``ti`` True indicates Texas Instruments, as opposed to Motorola, signal conventions. - ``crc`` can be None for no CRC, or a polynomial specifier. Note that the SPI clock frequency will not always be the requested baudrate. The hardware only supports baudrates that are the APB bus frequency (see :meth:`pyb.freq`) divided by a prescaler, which can be 2, 4, 8, 16, 32, 64, 128 or 256. SPI(1) is on AHB2, and SPI(2) is on AHB1. For precise control over the SPI clock frequency, specify ``prescaler`` instead of ``baudrate``. Printing the SPI object will show you the computed baudrate and the chosen prescaler. .. method:: SPI.recv(recv, *, timeout=5000) Receive data on the bus: - ``recv`` can be an integer, which is the number of bytes to receive, or a mutable buffer, which will be filled with received bytes. - ``timeout`` is the timeout in milliseconds to wait for the receive. Return value: if ``recv`` is an integer then a new buffer of the bytes received, otherwise the same buffer that was passed in to ``recv``. .. method:: SPI.send(send, *, timeout=5000) Send data on the bus: - ``send`` is the data to send (an integer to send, or a buffer object). - ``timeout`` is the timeout in milliseconds to wait for the send. Return value: ``None``. .. method:: SPI.send_recv(send, recv=None, *, timeout=5000) Send and receive data on the bus at the same time: - ``send`` is the data to send (an integer to send, or a buffer object). - ``recv`` is a mutable buffer which will be filled with received bytes. It can be the same as ``send``, or omitted. If omitted, a new buffer will be created. - ``timeout`` is the timeout in milliseconds to wait for the receive. Return value: the buffer with the received bytes. Constants --------- .. data:: SPI.MASTER .. data:: SPI.SLAVE for initialising the SPI bus to master or slave mode .. data:: SPI.LSB .. data:: SPI.MSB set the first bit to be the least or most significant bit