network — network configuration

This module provides network drivers and routing configuration. Network drivers for specific hardware are available within this module and are used to configure a hardware network interface. Configured interfaces are then available for use via the socket module.

For example:

# configure a specific network interface
# see below for examples of specific drivers
import network
nic = network.Driver(...)
print(nic.ifconfig())

# now use socket as usual
import socket
addr = socket.getaddrinfo('micropython.org', 80)[0][-1]
s = socket.socket()
s.connect(addr)
s.send(b'GET / HTTP/1.1\r\nHost: micropython.org\r\n\r\n')
data = s.recv(1000)
s.close()

class CC3K

This class provides a driver for CC3000 wifi modules. Example usage:

import network
nic = network.CC3K(pyb.SPI(2), pyb.Pin.board.Y5, pyb.Pin.board.Y4, pyb.Pin.board.Y3)
nic.connect('your-ssid', 'your-password')
while not nic.isconnected():
    pyb.delay(50)
print(nic.ifconfig())

# now use socket as usual
...

For this example to work the CC3000 module must have the following connections:

  • MOSI connected to Y8
  • MISO connected to Y7
  • CLK connected to Y6
  • CS connected to Y5
  • VBEN connected to Y4
  • IRQ connected to Y3

It is possible to use other SPI busses and other pins for CS, VBEN and IRQ.

Constructors

class network.CC3K(spi, pin_cs, pin_en, pin_irq)

Create a CC3K driver object, initialise the CC3000 module using the given SPI bus and pins, and return the CC3K object.

Arguments are:

  • spi is an SPI object which is the SPI bus that the CC3000 is connected to (the MOSI, MISO and CLK pins).
  • pin_cs is a Pin object which is connected to the CC3000 CS pin.
  • pin_en is a Pin object which is connected to the CC3000 VBEN pin.
  • pin_irq is a Pin object which is connected to the CC3000 IRQ pin.

All of these objects will be initialised by the driver, so there is no need to initialise them yourself. For example, you can use:

nic = network.CC3K(pyb.SPI(2), pyb.Pin.board.Y5, pyb.Pin.board.Y4, pyb.Pin.board.Y3)

Methods

cc3k.connect(ssid, key=None, *, security=WPA2, bssid=None)

Connect to a wifi access point using the given SSID, and other security parameters.

cc3k.disconnect()

Disconnect from the wifi access point.

cc3k.isconnected()

Returns True if connected to a wifi access point and has a valid IP address, False otherwise.

cc3k.ifconfig()

Returns a 7-tuple with (ip, subnet mask, gateway, DNS server, DHCP server, MAC address, SSID).

cc3k.patch_version()

Return the version of the patch program (firmware) on the CC3000.

cc3k.patch_program('pgm')

Upload the current firmware to the CC3000. You must pass ‘pgm’ as the first argument in order for the upload to proceed.

Constants

CC3K.WEP
CC3K.WPA
CC3K.WPA2

security type to use

class WIZNET5K

This class allows you to control WIZnet5x00 Ethernet adaptors based on the W5200 and W5500 chipsets (only W5200 tested).

Example usage:

import network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
print(nic.ifconfig())

# now use socket as usual
...

For this example to work the WIZnet5x00 module must have the following connections:

  • MOSI connected to X8
  • MISO connected to X7
  • SCLK connected to X6
  • nSS connected to X5
  • nRESET connected to X4

It is possible to use other SPI busses and other pins for nSS and nRESET.

Constructors

class network.WIZNET5K(spi, pin_cs, pin_rst)

Create a WIZNET5K driver object, initialise the WIZnet5x00 module using the given SPI bus and pins, and return the WIZNET5K object.

Arguments are:

  • spi is an SPI object which is the SPI bus that the WIZnet5x00 is connected to (the MOSI, MISO and SCLK pins).
  • pin_cs is a Pin object which is connected to the WIZnet5x00 nSS pin.
  • pin_rst is a Pin object which is connected to the WIZnet5x00 nRESET pin.

All of these objects will be initialised by the driver, so there is no need to initialise them yourself. For example, you can use:

nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)

Methods

wiznet5k.ifconfig([(ip, subnet, gateway, dns)])

Get/set IP address, subnet mask, gateway and DNS.

When called with no arguments, this method returns a 4-tuple with the above information.

To set the above values, pass a 4-tuple with the required information. For example:

nic.ifconfig(('192.168.0.4', '255.255.255.0', '192.168.0.1', '8.8.8.8'))
wiznet5k.regs()

Dump the WIZnet5x00 registers. Useful for debugging.